搜索结果: 1-14 共查到“机械工程 Aluminum”相关记录14条 . 查询时间(0.046 秒)
Microstructure and Mechanical Behavior of In Situ Primary Si/Mg2Si Locally Reinforced Aluminum Matrix Composites Piston by Centrifugal Cast
Piston Centrifugal casting In situ composite Primary Si Mg2Si
2011/8/5
Al-Si pistons are frequently damaged by burning piston top surface due to elevated combustion temperature, and, by rubbing the first ring groove against the engine cylinder liner. To prevent from thes...
Microstructure and Mechanical Behavior of In Situ Primary Si/Mg2Si Locally Reinforced Aluminum Matrix Composites Piston by Centrifugal Casting
Piston Centrifugal casting In situ composite Primary Si Mg2Si
2011/8/4
Al-Si pistons are frequently damaged by burning piston top surface due to elevated combustion temperature, and, by rubbing the first ring groove against the engine cylinder liner.
Multi-axial Fatigue of 2024-T4 Aluminum Alloy
2024-T4 aluminum alloy fatigue life loading path multiaxial fatigue
2011/8/4
Only the fatigue initiation is considered by the safe-life design approach, while fatigue crack propagation is paid more attention by the damage tolerance approach. The reasonable fatigue design metho...
New Inclusion Assessment Method in Aluminum Alloys —Electrochemical Method for Inclusion Assessment (EcMIA)
aluminum alloys inclusion assessment electrochemical parameters
2011/8/4
The existence of inclusion influences the properties of aluminum alloy castings, from which the castings will face scrapping under severe condition. Great efforts on the inclusions in aluminum alloy w...
Lateral extrusion of tailor welded aluminum alloy pipes with a lost core of low temperature melting alloy
Tube forming Tailored blank Lateral extrusion
2009/12/14
Purpose: In this paper, the authors employ tailor welded aluminum alloy pipes for lateral extrusion process with a lost core to perform a hollow light-weight-part.
Design/methodology/approach: The pi...
Resistance spot welding of aluminum alloy sheet 5J32 using SCR type and inverter type power supplies
Welding Aluminium sheet metal Spot welding
2009/12/3
Purpose: A characteristic was compared and analyzed between the lobe diagram of SCR type resistance spot welding and that of inverter type resistance spot welding of the aluminum alloy sheet 5J32 for ...
Casting of aluminum alloy strip using an unequal diameter twin roll caster
Casting Unequal diameter twin roll caster Strip casting
2009/12/2
Purpose: of this paper is to clear the property and ability of an unequal diameter twin roll caster to cast
commercial size strip. Therefore, 400mm-width strip was cast as first step. Surface-conditi...
A quality problem in seam welds in aluminum extrusion
Metallic alloys Seam weld Aluminum Extrusion Porthole die
2009/12/1
Purpose: Seam welds occur during the hollow profile extrusion; the billet’s material is divided into separate
metal streams by the bridges of the die which support a mandrel, and then these metal str...
Investigation of the Friction Behavior of the Zinc-Aluminum Based Commercial ZA-27 Journal Bearing
Zinc-aluminum alloy plain bearing friction lubrication
2009/10/13
The zinc-aluminum based ZA-27 alloy was produced by permanent mould casting. Using this alloy and bronze obtained from commercial sources, thin wall journal bearings were manufactured by machining. Th...
Laser Beam Welding of AA5052, AA5083, and AA6061 Aluminum Alloys
Laser Beam Welding AA5052 AA5083 AA6061 Aluminum Alloys
2009/9/2
The present investigation was mainly concerned with characteristics of autogeneous laser butt welding of 2 mm thickness nonheat treatable AA5052-H12, AA5083-H12 and 2 mm, 3 mm thickn...
Microstructure quantitative analysis of aluminum skeleton castings
Skeleton casting Core AlSi alloy Microstructure
2011/3/17
In this article authors showed method for manufacturing of closed skeleton castings with hypo – eutectic and eutectic aluminium alloys.
Physico-chemical characteristic of aluminum alloy castings manufactured with cores containing fly ash as a base material
Innovative foundry materials and technologies Fly ash Aluminum alloy Structure
2011/3/15
Castings were poured from PA9 aluminum alloy. Cores in the form of standard cylindrical specimens were made from the core mixture based on fly ash of the identified chemical and granular composition.
High speed twin roll caster for aluminum alloy thin strip
Twin roll casting Recycle aluminum alloy Thin strip
2010/2/10
Design/methodology/approach: The effects of the high-speed twin roll caster on alleviating the deterioration of mechanical properties by impurities were investigated. Properties of the cast strip were...
期刊信息
篇名
Changes of H+ pumps of tonoplast vesicle from wheat roots in vivo and in vitro under aluminum treatment and effect of calcium.
语种
英文
撰写或编译
作者
Zhang WH,Zhang FQ,Shen ZG and Liu YL.
第一作者单位
刊物名称
...